Products

Aceproof Marvel


Description

ACEPROOF MARVEL is an excellent quality, tough and carefully premixed liquid waterproof membrane. It is ready-to-use, self-curing, hydrostatic pressure resistance waterproofing underlayment that forms very strong yet flexible film which provides good adhesion to many surfaces and accommodates normal building movements without rupture.

  • 800% Elongation
  • Single component, ready to use
  • Water based, safe to use, low odour
  • Resists fungi and algae growth
  • Adhesion to most substrates

Uses:

  • Interior and exterior application for commercial and residential use
  • Underwater applications – Swimming pools, fountains, water tank, fish tank, etc
  • Kitchens, bathrooms, laundries, food processing areas, etc

Mixing
  • Once surface preparation is over, then open the pail and stir properly
  • Apply mixed material on to the prepared substrate using a brush or roller
  • Two coats are recommended for excellent result. Apply subsequent coat after 1-2 hours curing of previous coat
  • Maintain each coat thickness of 0.8mm and not more than 1 mm
  • Allow 14-16 hours curing of final coat before laying screed or tiling
  • Flood test can be conducted after 24 hours of final coat

Aceproof Marvel

Area Unit Calculator
Area to be Covered metres sq.
Quantity required in litre’s
1 litre can required (2 coats of 1.5mm thickness)
5 litre can required (2 coats of 1.5mm thickness)
20 litre pail required (2 coats of 1.5mm thickness)
Note: Add 10% for wastage at site

Recommended substrates:
  • Concrete, cement mortar beds, cement plasters, etc.
  • Plywood and other dry wall applications
  • Concrete masonry, brick masonry, cement terrazzo, etc.
Surface preparation
  • Surfaces must be structurally strong
  • Remove all grease, oil, dirt, curing compounds, sealers, adhesives or any other contaminant that would prevent good bonding
  • Concrete or plaster must be cured 28 days prior to bonding unless it is made with Acescreed or Aceplast
  • Dampen the surface before application of water proofing coating but make sure no free standing water is present during application
Pack size:

Available in 1 ltr, 5 ltr and 20 ltr pack size

Coverage

Approximately 350 sft per 20 ltr pail for 2 coats of 1.5 mm thickness. Coverage will vary depending on surface undulation and application variances.

Shelf life:

12 months, if stored in cool and dry area in unopened containers, protected from sun light. Shelf life is calculated from the month of manufacturing of the product.

Curing and Protective Measures

Curing time is affected by ambient, surface temperatures and humidity. Water proofed area should be completely covered up to 24 hours. Flood test can be conducted after 24 hours and then area should be protected either laying tiles or plastering it. Generally, light foot traffic can be allowed in 24 hours at 25°C, normal foot traffic in 48 hours and heavy foot traffic in 7days after installation of tiles or protective coat.

Caution
    • Store in cool and dry place.
    • High temperature or moisture will affect the product.
    • Once container is opened, then finish it off without keeping for long time.
    • This product contains latex based emulsion and other chemical additive. Avoid eye contact or prolonged contact with skin.
    • Wash thoroughly after handling. If eye contact occurs, flush with water for 15 minutes and consult a physician.
    • Do not breathe directly; wear PPE whenever necessary
CURING AND PROTECTIVE MEASURES

Curing time is affected by ambient, surface temperatures and humidity. Water proofed area should be completely covered up to 24 hours. Flood test can be conducted after 24 hours and then area should be protected either laying tiles or plastering it. Generally, light foot traffic can be allowed in 24 hours at 25°C, normal foot traffic in 48 hours and heavy foot traffic in 7days after installation of tiles or protective coat.