Products
Acescreed-Concentrated
Product Lists
- Acescreed Concentrated
- Antirust Coating
- Block Fixing Mortar
- Bonding Agent
- Cementitious Grout
- Cleaner
- Crack Filler
- Enhancer
- Epoxy Adhesive
- Epoxy Coating
- Epoxy grout
- Grouts
- Mould Releasing Agent
- PU Adhesive
- Screed
- Sealers
- Slurry Additive
- Sparkling Series
- Special Adhesive
- Special Admixture
- Thickbed Mortar
- Thin Set Adhesive
- Tile Adhesive
- Tiles and Stone care
- Wall Care
- Waterproofing
ACESCREED – Concentrated is a cementitious screeding material prepared by using high performance ingredients, premium cement and treated fillers. It is a self-curing screed designed for use with required proportion of water and aggregates at site. It is also designed for mix with a small proportion of ACEMIX TBL for increased performance.
THICKNESS | ACESCREED | Aggregates | ACEMIX TBL | Water(Approx) | Coverage(Approx) |
---|---|---|---|---|---|
12 mm | 30 kg | 180 kg | 2.0 l | 7.0 l | 84 sft |
25 mm | 30 kg | 180 kg | 2.0 l | 7.25 l | 45 sft |
35 mm | 30 kg | 180 kg | 2.0 l | 7.5 l | 27 sft |
50 mm | 30 kg | 180 kg | 2.0 l | 8.0 l | 20 sft |
- Mixing Ratio:Refer table
- Pot Life:Approx 1.5 hrs
- Time to normal foot traffic18-24 hrs
- Time to heavy foot trafficAfter 72 hrs
- Compressive strength:>25 MPa
- Flexural strength>5MPa
- Tensile strength >2MPa
Mixing
Mix 1 bag of ACESCREED with 4 to 12 bags of sand (weight to weight basis) based on the strength requirement and purpose of application. Use approximately 10-12 litre or required amount of liquid (either water or mixture of water and Acemix TBL latex admix) for 30 kg powder. Add liquid to the pre-blended powder slowly under mixing. Mix by hand or use a medium speed drill mixer (250 – 500 rpm speed) to achieve a smooth, paste-like consistency. It can also be mixed by creating a well in the middle of the mixed product, gradually add pre-measured water mixing the product by shovel or trowel until a dry but moist workable mix is achieved. Stir occasionally, but do not add more water. Transfer the mixed product into a clean container and carry and pour into recess.
- Self-curing. No need of water curing.
- Tiles can directly be bed-in immediately
- Easy mix with water or latex
- Easy spreadability, high workability, water resistant
- Easy to apply and level, Fast acting and cost efficient
- Very high mechanical strength, shock and impact resistance
- Can be mixed with locally available sand
Uses:
Interior and exterior application for domestic, residential, commercial and industrial floors.
Interior and exterior application for domestic, residential, commercial and industrial floors.
Acescreed Concentrated |
||||
---|---|---|---|---|
Bag Calculator | ||||
Screeding area | metres sq. | Quantity required in kg’s | ||
Bed Thickness | mm | kg mix required | ||
Acescreed Concentrated(kg) | Sand/Aggregates(kg) | No. of Acescreed Concentrated of 30kg bags required | ||
Acescreed:Sand ratio | 1:4= | |||
1:5= | ||||
1:6= | ||||
1:7= | ||||
1:8= | ||||
1:9= | ||||
1:10= | ||||
1:11= | ||||
1:12= | ||||
Note: Mix 1litre Acemix TBL for 30kg Acescreed concentrated |
Recommended substrates:
Old or new concrete floors, cement beds, etc whose compressive strength is greater than 25 MPa.
Surface preparation
Surfaces must be structurally strong. Remove all grease, oil, dirt, curing compounds, sealers or any other contaminant that would prevent good bonding. Glossy, lime washed or painted surfaces must be sanded, or abraded, and stripped off all contaminants. Concrete floor must be free of efflorescence and not subject to hydrostatic pressure. Concrete floors should have a course finish to enhance the bond. Roughen the surface by sanding or abrading, then rinse and allow to dry. Use recommended ACEMIX bonding agent for proper bonding between the floor and screed. Expansion joints should never be bridged with setting material. Surface temperature should be maintained above 10° C or below 38° C to achieve proper bonding. For questions about proper installation, call Technical Services executives on +91 963 260 5577.
Pack size:
Available in 30 kg bags in grey colour
Shelf life:
12 months if stored in cool and dry area in unopened bag. Shelf life is calculated from the month of manufacturing of the product.
Caution:
- Store in cool and dry place.
- High temperature will affect the product.
- Once pack is opened, then finish it off without keeping for long time.
- This product contains epoxy material. Avoid eye contact or prolonged contact with skin.
- Wash thoroughly after handling. If eye contact occurs, flush with water for 15 minutes and consult a physician.
- Do not breathe closely; wear PPE whenever necessary.
THICKNESS | ACESCREED | Aggregates | ACEMIX TBL | Water(Approx) | Coverage(Approx) |
---|---|---|---|---|---|
12 mm | 30 kg | 180 kg | 2.0 l | 7.0 l | 84 sft |
25 mm | 30 kg | 180 kg | 2.0 l | 7.25 l | 45 sft |
35 mm | 30 kg | 180 kg | 2.0 l | 7.5 l | 27 sft |
50 mm | 30 kg | 180 kg | 2.0 l | 8.0 l | 20 sft |