Acefix TBA + Acemix TBL


Acefix TBA: Premium grade thick bed mortar designed for mix with Acemix TBL and water at site. It is a premixed mortar prepared with high quality chemical ingredients, treated aggregates and speciality polymers. It offers high bond strength and excellent handling property for a wide variety of floor application up to 40mm bed thickness.

ACEMIX TBL: Concentrated latex admixture diluted with water on site and then mixed with ACESCREED or ACEPLAST to make cement screed, cement plasters and thick mortar beds to get very high mechanical property and improved physical characteristics of the bed.

  • Mixing ratio:Refer table
  • Pot Life: Approx 4Hrs
  • Time to normal foot traffic: 18-24 hrs
  • Time to heavy foot traffic:After 72 hrs
  • Compressive strength:> 20 MPa
  • Flexural strength:>4 MPa
  • Tensile strength:>2 MPa

Use required amount of Acemix TBL and water for 30 kg powder. Add liquid to the pre-blended powder slowly under mixing. Mix by hand or use a medium speed drill mixer (250 – 500 rpm speed) to achieve a smooth, paste-like consistency.

It can also be mixed by creating a well in the middle of the mixed product, gradually add pre-measured water mixing the product by shovel or trowel until a dry but moist workable mix is achieved. Stir occasionally, but do not add more water. Transfer the mixed product into a clean container and carry and pour into recess.

  • Premium grade, strong bonding.
  • Self-curing. No need of water curing.
  • Tiles can directly be bed-in immediately.
  • Superior quality, Easy to use.
  • Good workability, easy mix with liquid.
  • High performance, low shrinking.
  • High compressive, flexural and tensile strength.
  • Very high flexibility with high bonding property
  • High compressive strength and thermal shock resistance..
  • High adhesion and lower water absorption.
  • High adhesion and lower water absorption.
  • High impact resistance, high mechanical property.
  • No degradation on long term exposure.

Interior and exterior applications for floor and wall.

For facades, tile on tile and submerged application.

Recommended substrates:

Old or new concrete floors, cement beds, etc whose compressive strength is greater than 25 MPa.

Cement floors, concrete bed


Surface preparation

Surfaces must be structurally strong. Remove all grease, oil, dirt, curing compounds, sealers or any other contaminant that would prevent good bonding. Glossy, lime washed or painted surfaces must be sanded, or abraded, and stripped off all contaminants. Concrete floor must be free of efflorescence and not subject to hydrostatic pressure. Concrete floors should have a course finish to enhance the bond. Roughen the surface by sanding or abrading, then rinse and allow to dry. Use recommended ACEMIX bonding agent for proper bonding between the floor and screed. Expansion joints should never be bridged with setting material. Surface temperature should be maintained above 10° C or below 38° C to achieve proper bonding. For questions about proper installation, call Technical Services executives on +91 963 260 5577.

Pack size:

Available in 1 ltr, 5 ltr and 20 ltr pack size.

Shelf life:

12 months if stored in cool and dry area in unopened bag. Shelf life is calculated from the month of manufacturing of the product.

  • Store in cool and dry place.
  • High temperature will affect the product.
  • Once pack is opened, then finish it off without keeping for long time.
  • This product contains epoxy material. Avoid eye contact or prolonged contact with skin.
  • Wash thoroughly after handling. If eye contact occurs, flush with water for 15 minutes and consult a physician.
  • Do not breathe closely; wear PPE whenever necessary.
12 mm 30 kg 1.5 ltr 6.0 ltr 24 sft
25 mm 30 kg 1.2 ltr 6.3 ltr 13 sft
35 mm 30 kg 1.0 ltr 6.5 ltr 9 sft
50 mm 30 kg 0.75 ltr 6.75 ltr 6 sft